10×330 Zirconia Sanding Belts 60 Grit – 25 Pack

Pack of 25 — $27.50
($1.10 each)

60-grit zirconia sanding belts for precision sanding, weld blending and deburring in confined areas.

  • Belt Size: 10 × 330 mm
  • Pack quantity: 25 per pack
Technical Specifications
SpecificationDetails
BrandX Flex
Product TypeSanding Belt
Belt Size10 × 330 mm
Abrasive / GritZirconia G60
BackingCloth backing (verify packaging)
Joint TypeVerify packaging
Compatible MachineBelt sander or linisher accepting 10 × 330 mm belts
ApplicationGrinding, deburring, sanding and surface preparation
Pack Quantity25 belts
Country of ManufactureVerify packaging

10×330 Zirconia Sanding Belts 60 Grit

X Flex 10×330 Zirconia Sanding Belts 60 Grit — pack of 25.

60-grit zirconia sanding belts for precision sanding, weld blending and deburring in confined areas.

Applications

  • Precision sanding of small metal components.
  • Weld blending and finishing in confined areas.
  • Deburring sharp edges and corners.
  • Surface preparation before coating or painting.

Size and Compatibility

  • Belt Size: 10 × 330 mm
  • Abrasive / Grit: Zirconia G60
  • Compatible machine: Belt sander or linisher accepting 10 × 330 mm belts
  • Pack quantity: 25 per pack

Check the product label and machine instructions for fitting, operating speed and safe use before starting work.

Browse the X Flex abrasive range for other sizes and workshop consumables.

Reviews

There are no reviews yet.

Be the first to review “10×330 Zirconia Sanding Belts 60 Grit – 25 Pack”

Your email address will not be published. Required fields are marked *

Store sanding belts in a clean, dry environment away from moisture, excessive heat, direct sunlight and physical damage. Keep belts in their original packaging until ready for use to maintain optimum performance and maximise service life.

SectionDetails
Ideal Applications Precision sanding of small metal components.
Weld blending and finishing in confined areas.
Deburring sharp edges and corners.
Surface preparation before coating or painting.
Suitable Materials Mild steel.
Stainless steel.
Aluminium.
General metal fabrication.
Recommended MachineBelt sander or linisher compatible with 10 × 330 mm sanding belts.
Best ForMetal fabricators, engineering workshops, maintenance professionals and DIY users requiring narrow belts for detailed sanding and finishing tasks.
Do Not Use For Incorrect machine size.
Damaged or torn belts.
Excessive pressure during sanding.
Machines with poor belt tracking.
Practical Workshop NoteCheck belt alignment before starting the machine and maintain proper belt tension to maximise cutting efficiency and belt life.

Sanding belts are designed for use on belt sanders and linishing machines for grinding, sanding, deburring and surface preparation. Correct belt tracking, machine setup and safe operating practices are essential for optimum performance.

SectionDetails
Intended UseGrinding, weld blending, edge finishing, deburring, stock removal and surface preparation on suitable metal materials.
Compatible MachineBelt sander or linisher designed to accept 10 × 330 mm sanding belts.
Before UseInspect the belt for tears, damaged joints, moisture damage, excessive wear or other visible defects. Do not use damaged or worn belts.
PPEWear safety glasses or a face shield, hearing protection, suitable gloves, protective clothing, safety footwear and respiratory protection where dust may be generated.
Speed CheckEnsure the machine operating speed does not exceed the maximum speed or RPM specified on the product packaging.
GuardingAlways operate with the appropriate machine guards installed. Never remove guards or modify equipment to fit incorrect belt sizes.
Never Use ForIncorrect belt size, damaged belts, poor belt tracking, loose guards, unsupported workpieces or wet applications unless the belt is specifically designed for wet use.

● Check belt direction, tracking and tension before starting the machine.
● Allow the belt to reach full operating speed before contacting the workpiece.
● Hold the workpiece securely throughout the sanding process.
● Apply consistent, moderate pressure to avoid overheating the abrasive.
● Keep hands clear of moving belts, rollers and pinch points.

● Using a torn or damaged sanding belt.
● Ignoring poor belt tracking.
● Applying excessive pressure to increase material removal.
● Allowing the workpiece to contact belt joints aggressively.
● Selecting the wrong grit for the required finish.

More from Sanding & Linishing Belts

  • Sanding & Linishing Belts

    100x914mm Zirconia Linishing Belt 60 Grit – 10 Pack

    Pack of 10 — $68.00
    ($6.80 each)
    Add to cart
  • Sanding & Linishing Belts

    75x2000mm Zirconia Linishing Belt 60 Grit – 10 Pack

    Pack of 10 — $97.50
    ($9.75 each)
    Add to cart
  • Sanding & Linishing Belts

    50x914mm Zirconia Linishing Belt 60 Grit – 10 Pack

    Pack of 10 — $40.00
    ($4.00 each)
    Add to cart
  • Sanding & Linishing Belts

    50x1220mm Zirconia Linishing Belt 60 Grit – 10 Pack

    Pack of 10 — $48.00
    ($4.80 each)
    Add to cart

Frequently Asked Questions

What is this sanding belt used for?

60-grit zirconia sanding belts for precision sanding, weld blending and deburring in confined areas.

Which machine and fitting should I check?

Belt sander or linisher accepting 10 × 330 mm belts. Match the product dimensions and fitting to your tool. Check the product label and machine instructions for the permitted operating speed and setup.

How many are supplied in a pack?

Pack of 25.

Shopping Cart